Aviom MixSP

Aviom MixSP Personal System

The MixSP Standalone Personal Mixing System is the perfect plug-n-play 6-mixer monitor system for everything from silent rehearsals to live gigs.

DISCONTINUED
Item

GET QUOTE

 Guaranteed Lowest Price
100% Satisfaction Guarantee
Free Freight on most products
Lifetime Technical Support
Easy Financing
Our Low Price Guarantee

The MixSP Standalone Personal Mixing System is the perfect plug-n-play 6-mixer monitor system for everything from silent rehearsals to live gigs.

It allows you to connect mics and/or line-level signals directly to the Pro16 input module without need for a console. The built-in XLR passive split on the AN-16/i-M Mic Input Module can be used to connect the input signals to a PA system or mixing console and retain independent control over the monitor content. It's the perfect solution for performers who travel; no more worrying about the monitor system at the gig!

Once the input signals are connected to the AN-16/i-M Mic Input Module, connect a Cat-5e cable from the AN-16/i-M to the A-16D Pro A-Net Distributor which copies and splits the digital signal while at the same time adding DC power to each of its eight outputs.

Connecting a Cat-5e cable from the A-16D Pro to each A-16II Personal Mixer is all that is necessary to complete the setup; the mixers get their power over the same cable that delivers the 16-channel digital signal. Plug headphones, ear buds, or a wireless in-ear monitoring system into the Personal Mixer and you're ready to start creating custom mixes.

The AN-16/i-M Mic Input Module used as the head-end of this system contains 16 high-quality microphone preamps with 24-bit A-to-D converters. Each of its channels contains a continuously variable gain knob, phase reverse switch, 48-volt phantom power, and a rumble filter with an 85Hz rolloff.

The 16-channel A-16II Personal Mixer allows a performer to create and save up to 16 custom mixes, and gives each performer control over channel volume, grouping, pan, stereo spread, along with master volume and tone. The system also includes an MT-1 for each Personal Mixer to allow the personal mixer to be mounted on any standard mic stand.

  • 1 AN-16/i-M Mic Input Module
  • 1 A-16D Pro A-Net Distributor
  • 6 A-16II Personal Mixers
  • 6 MT-1a Mic Stand Mounts
  • 7 L-25 Cat-5e Cables

The A-16D Pro A-Net Distributor eliminates the need to daisy chain Personal Mixers, and simplifies set-up by eliminating the need to connect a power supply to each mixer. The A-16D Pro accepts one Pro16 A-Net input signal and provides nine parallel outputs, using rugged EtherCon connectors and standard Cat-5e cables. The A-16D Pro provides isolated (floating ground) DC power through the eight A-Net Outs; the ninth output is an unpowered A-Net Thru connector, designed for distributing a copy of the A-Net signal to a second A-Net Distributor or remote location.

As with all Aviom personal mixing systems, this six-mix package can be expanded as needed to include more Personal Mixers at any time.


MixSP Technical Specifications

AN-16/i-M Mic Input Module

Audio Inputs XLR Input
(mic/line) TRS Line Inputs, &
Send/Return Audio Thru Insert Send Insert Return Analog to Digital Conversion Operating Level Frequency Response A-Net Output A-Net Expansion Gain Range Channel LED Indicators Line Inputs Metering Stereo Operation Maximum Input Level Input Impedance A/D Freq. Response THD +N Crosstalk Bit Error Rate (BER) Signal to Noise (unweighted) EIN (Equivalent Input Noise) CMRR (Common Mode Rejection Ratio) Low Cut Filter Phantom Power Digital Outputs Pro16 A-Net Latency Power Supply Voltage Dimensions Weight
16, balanced mic- or line-level, XLR combo connector
Pin 1: Ground; Pin 2: Audio +; Pin 3: Audio -
Tip: Audio +; Ring: Audio -; Sleeve: Ground
XLR; Pin 1: Ground; Pin 2: Audio +; Pin 3: Audio -
Direct coupled passive throughput
Impedance balanced; Nominal level: 0dBu; Peak
Level (A/D clip point): +14dBu
The Insert Send connector is a line output in the signal path post gain, post filter, and post phase controls.
TRS balanced; Nominal level: 0dBu; Peak Level
(A/D clip point): +14dBu
The Insert Return connector is a line input to the signal path that is pre A/D conversion.
48kHz sample rate, 24 bit
+4dBu
4Hz-22kHz
One Category 5 (RJ45 connector)
One Category 5 (RJ45 connector)
Mic: +6dB to +60dB; Line: -15dB to +36dB
Signal Present and Clip, per channel
Impedance: 48k ohms
LEDs; green: Signal Present, red: Clip; per channel
Stereo Link, per channel pair;
Two-position switch (Normal, Link)
Mic: +14dBu; Line: +28dBu
Mic: 2.4k ohms; Line (TRS): 33k ohms;
Insert Return: 39k ohms
-0.1dB @ 20kHz (-0.4dB @ 20.0kHz, measured
from Mic or Line in)
-3dB @ 1.5Hz (-3dB @ 2.0Hz, measured from Mic or Line in)
< 0.003%
-90dB
10(-12)
A/D: -105dB Reference = +14dBu (A/D clip point) Send jack: -113dB (Gain = minimum)
-128dBu
(Rs = 150 ohms, 20kHz BW, Gain = +60dB)
80dB @
120Hz (Gain = +60dB)
-3dB @ 85Hz, -18 dB per octave
+48 volts, per channel, switch with LED
A-Net: 2 (Main and Aux); A-Net Expansion: 1

A-Net Expansion combines two A-Net streams (32 channels of audio) onto one Cat-5e cable
uses unshielded Cat-5e UTP (or better) cable

<0.880 msec (measured from analog input to analog output)
Internal, universal switching type; IEC jack
100-240VAC, 50-60Hz, 60W; Fuse: 250VAC, F4AL
19 x 9.25 in. (482.6 x 234.95mm); 3U high
12 pounds (5.44 kg)

 

A-16II Personal Mixer

Audio Output Line/Headphone TRS Output A-Net Input/Output Digital to Analog Conversion Bit Depth Signal to Noise Ratio Latency Pro16 A-Net Tone Controls Maximum Levels (RMS) Impedance Power Supply
      Input Voltage
      Output Voltage
      Plug Size Dimensions Weight Options
1/4-inch TRS stereo, headphone or line level
Tip: Audio Left; Ring: Audio Right;Sleeve: Ground
Auto-detects mono plugs
1 A-Net input, 1 A-Net output; Category 5 (RJ45 connector)
24 bit
(Referenced to 0dB) -103dB
<0.880 msec (measured from analog input to analog output)
Uses unshielded Cat-5e UTP (or better) cable; maximum 500ft (150m) between devices
Treble +/-12dB at 9kHz shelving
Bass +/-12dB at 160Hz shelving
Line/Headphone outs: 1.0 watt at 100 ohms
Line/Headphone outs: 32 ohms
External, DC, universal switching type
100-240 volts, 50/60Hz, 30VA
18-24 VDC, 0.5 amp
2 mm
10.75" (273 mm) wide x 5.6" (142.2 mm) deep;
2.25" (57.5 mm) high 
3.4 lbs. (1.54 kg)
MT-1 or MT-1a Mic Stand Mount
EB-1 Extension Bracket
MT-X Expansion Box (requires MT-1)
PS-120 Power Supply

 

A-16D Pro A-Net Distributor

A-Net Input A-Net Thru A-Net Outputs LEDs Pro16 A-Net Power Supply Cooling Input Voltage Output Voltage for
Personal Mixers Dimensions Weight
One EtherCon RJ45 connector
One EtherCon RJ45 connector, unpowered
8 EtherCon RJ45 connectors, powered (DC)
Power On; A-Net Active
16 channels of digital audio over Cat-5e cable
Uses unshielded Cat-5e UTP (or better) cable
Internal, universal switching type
One ultra-quiet fan
100-240VAC, 50-60Hz, 60W
18-24 VDC, 0.5 amp
Transmitted over the Cat-5e cable
19" (482.6 mm) wide x 14.25" (362 mm) deep; 2U,
3.5" (88.9 mm) high
12.0 lbs (5.44 kg)

 

MT-1a Mic Stand Mount

Boxed Weight Boxed Dimensions Dimensions Connections: Connectors:
1 lb
7"w x 5"d x 3"h
6.25" wide at front x 4.5" wide at rear x 3" high
Attaches with three screws to bottom of an A360 A-16II, or A-16CS
Size: 6-32, 1/4-inch long screws

Call 1-877-477-6432 for any technical questions or if you need SPECIAL PRICING regarding this product