Aviom Mix4D

Aviom Mix4D

Avioms Four-Mix Personal Mixing System with the A16D

DISCONTINUED
Item

GET QUOTE

 Guaranteed Lowest Price
100% Satisfaction Guarantee
Free Freight on most products
Lifetime Technical Support
Easy Financing
Our Low Price Guarantee

The Aviom Mix4D is a complete monitor Mixing System for 4 performers.

It easily connects to any analog console using the console's line-level outputs, direct outs, aux sends, groups, or busses.

At the head end, line-level input signals are connected to the AN-16/i v.2 Input Module, which converts the analog signals to digital. Connect the included Cat-5e cable from the AN-16/i v.2 to the A-16D A-Net Distributor which copies and splits the digital signal, eliminating daisy chain connections. Connect the four PS-120 power supplies to the DC jacks on the rear of the A-16D to send DC power over the Cat-5e cables to the Personal Mixers.

Finally,connecting a Cat-5e cable from the powered A-16D jacks to each A-16II Personal Mixer is all that is necessary to set up the system; the mixers get their power over the same cable that delivers the 16-channel Pro16® A-Net® digital signal. Plug headphones, ear buds, or a wireless in-ear monitoring system into the Personal Mixer and you're ready to start creating custom mixes

The Mix4D system's head end includes an AN-16/i v.2 Input Module which accepts up to 16 line-level inputs. Audio is converted to digital and transmitted via A-Net®, up to 500ft/150m over Cat-5e. A dedicated audio thru is available for each input channel, allowing the AN-16/i v.2 to be seamlessly inserted into an existing audio signal path.

The 16-channel A-16II Personal Mixer allows a performer to create and save up to 16 custom mixes, and gives each performer control over channel volume, grouping, pan, stereo spread, along with master volume and tone. The system also includes an MT-1a for each Personal Mixer to allow the Personal Mixer to be mounted on any standard mic stand.

  • 1 AN-16/i v.2 Input Module
  • 1 A-16D A-Net Distributor
  • 4 A-16II Personal Mixers
  • 4 MT-1a Mic Stand Mounts
  • 5 L-25 Cat-5e Cable
  • 4 PS-120 Power Supply

The A-16D A-Net Distributor eliminates the need to daisy chain Personal Mixers, and simplifies set-up by eliminating the need to connect a power supply to each mixer. The A-16D accepts one Pro16 A-Net input signal and provides eight parallel outputs, using standard Cat-5e connectors and cables. The A-16D can provide DC power for up to eight A-Net Outs by simply plugging a PS-120 power supply into the DC jacks on its rear panel.

As with all Aviom personal mixing systems, this four-mix package can be expanded as needed to include more Personal Mixers at any time.


Mix4D Technical Specifications

 

AN-16/i v.2 Input Module

Audio Inputs Inputs TRS Thru Analog to Digital Conversion Frequency Response A- Net In A-Net Out Gain Settings Channel LED Indicators Line Inputs Metering Stereo Operation Maximum Input Level Input Impedance Freq. Response THD +N Crosstalk Bit Error Rate (BER) Signal to Noise (unweighted) Digital Outputs A-Net Pro16 and Pro16e Latency Power Supply
      Input Voltage
      Output Voltage
      Plug Size Power Dimensions Weight Options
16, balanced line-level, 1/4-inch TRS connector
Tip: Audio +; Ring: Audio -; Sleeve: Ground
Impedance matched output
48kHz sample rate, 24 bit
4Hz-22kHz
One Category 5 (RJ45 connector)
Four-position slot range selector switch for use with Pro16e A-Net
One Category 5 (RJ45 connector)
Supports Pro16 and Pro16e
Four-position switch, -10dBv, 0dBu, +4dBu, and +22dBu
Signal Present and Clip, per channel
Impedance: 48k ohms
LEDs; green: Signal Present, red: Clip; per channel
Stereo Link, per channel pair;
Two-position switch (Normal, Link)
+22dBu
17.8k ohm
4Hz-22kHz +0.2dB/-3dB
< 0.003%
-90dB
10(-12)
90dB typical, A/D to D/A
Measured from AN-16/i to AN-16/o Output Module
A-Net: 1; RJ45 connector

Use unshielded Cat-5e UTP (or better) cable

<0.880 msec (measured from analog input to analog output)
External, DC, universal switching type
100-240 volts, 50/60Hz, 30VA
18-24 VDC, 0.5 amp
2 mm
18-24 VDC, 500mA
19" (482.6 mm) wide x 5.75" (146 mm) deep;
1U high
6.8 lb (3.08 kg)
AN-16SBR System Bridge; used to combine up to four A-Net streams for transmission over one Cat-5e cable

 

 

A-16II Personal Mixer

Audio Output Line/Headphone TRS Output A-Net Input/Output Digital to Analog Conversion Bit Depth Signal to Noise Ratio Latency Pro16 A-Net Tone Controls Maximum Levels (RMS) Impedance Power Supply
      Input Voltage
      Output Voltage
      Plug Size Dimensions Weight Options
1/4-inch TRS stereo, headphone or line level
Tip: Audio Left; Ring: Audio Right;Sleeve: Ground
Auto-detects mono plugs
1 A-Net input, 1 A-Net output; Category 5 (RJ45 connector)
24 bit
(Referenced to 0dB) -103dB
<0.880 msec (measured from analog input to analog output)
Uses unshielded Cat-5e UTP (or better) cable; maximum 500ft (150m) between devices
Treble +/-12dB at 9kHz shelving
Bass +/-12dB at 160Hz shelving
Line/Headphone outs: 1.0 watt at 100 ohms
Line/Headphone outs: 32 ohms
External, DC, universal switching type
100-240 volts, 50/60Hz, 30VA
18-24 VDC, 0.5 amp
2 mm
10.75" (273 mm) wide x 5.6" (142.2 mm) deep;
2.25" (57.5 mm) high 
3.4 lbs. (1.54 kg)
MT-1 Mic Stand Mount (uses 6-32 1/4-inch screws)
EB-1 Extension Bracket
MT-X Expansion Box (requires MT-1)

 

 

A-16D A-Net Distributor

A-Net Inputs A-Net Outputs Remote DC Power Inputs Output Voltage for Personal Mixers Main DC Power Input LED Indicators A-Net LED Indicators Remote DC Power Active LED Size Weight
One Category 5 (RJ45 connector)
8 Category 5 (RJ45 connector), optionally powered (DC)
8; Rear panel; accepts power supplies from A-16II or A-16R;
Size: 2mm
18-24 VDC, 0.5 amp
Transmitted over the Cat-5e cable
One; accepts included external DC power supply, universal switching type
Power On, Yellow
A-Net Active, Green
One per A-Net output
8.5" (215 mm) wide x 6.7" (170 mm) deep
1.2" (30.4 mm) high;
Can be rack-mounted on a standard 1U rack accessory shelf (optional)
2.0 lb (0.91 kg)

 

MT-1a Mic Stand Mount

Boxed Weight Boxed Dimensions Dimensions Connections: Connectors:
1 lb
7"w x 5"d x 3"h
6.25" wide at front x 4.5" wide at rear x 3" high
Attaches with three screws to bottom of and A360 A-16II, or A-16CS
Size: 6-32, 1/4-inch long screws

Call 1-877-477-6432 for any technical questions or if you need SPECIAL PRICING regarding this product